Barbed Wire pinstripe by Sharpline. 1/2 inch wide by 150 feet long. Available in black, silver, or gold on clear vinyl so vehicle's color shows through.
Now: $48.80
NEW for 2008 from Speed Graphics! This hot new eagle graphic is 13" x 72" and comes as a pair, one graphic for the left and one for the right side of your vehicle.
Was: $235.00Now: $208.00
The Hot Rod Graphic Kit measures 11 inches by 130 inches.
The Mach1 Graphic Kits come in two sizes and 9 colors. One measures 6 inches by 120 inches. The other measures 4 inches by 76 inches.
NEW for 2008 from Speed Graphics, Panthera! Choose this rrrrrrreckless new 'kitty' graphic in one of two colors. Available in two sizes. Comes as a pair, one graphic for the left and one for the right side of your vehicle.
Polished Stainless Steel Pillar Posts! A mirror shine that wows! Easy installation. These kits are custom made to fit your vehicle perfectly.
As soon as you drive out of the parking lot, your new vehicle's paint job will encounter stones, rocks, and road debris. Before long, your car's finish will become chipped and dull. Prevent costly repairs. Crystal clear StoneShield by Avery Dennison is your solid choice for Paint Protection. Avery's thin StoneShield™ polyurethane formula adds ideal protection for high visibility areas. It's virtually invisible in the showroom and after years of driving.
Now: $0.00
The Strata Graphic Kits come in two sizes. One measures 6.5 inches by 76 inches. The other measures 6.5 inches by 120 inches.
NEW for 2008 from Speed Graphics! Display your patriotism with this USA Flame Thrower graphic. The 15" x 100" graphic comes as a pair, one graphic for the left and one for the right side of your vehicle.
Overview | Why More Important Than Ever! | Step by Step Instructions
Tools required: masking tape, scissors, squeegee, lint-free cloth, TFX® CLEANER, ruler.
Application temperature should be above 50° F (13° C). If extremely cold, move to an enclosed area and allow the surface temperature to warm. If extremely hot, move to a shaded area.
Please refer to TFX Pro System for specific temperature recommendations.
Step1 Clean the surface with TFX® CLEANER or a few drops of grease-cutting liquid detergent in water (do not use a petroleum base cleaner). Rinse clean with fresh water then dry with a lint-free cloth. Wiping surface with alcohol will also help remove any contamination and enhance the adhesion process.
Please refer to TFX Pro System for additional cleaning procedures.
Step 2 Put a piece of masking tape on each end of your vinyl transfer in the area where you plan to apply it and anchor each end to the application surface with masking tape.
Step 3 Estimate the center of your vinyl transfer and place two vertical lengths of masking tape to secure the vinyl transfer and create a center hinge as shown in the illustration. This step allows you to apply half of the vinyl transfer at a time.
Step 4 Remove the masking tape anchor from one end of your vinyl transfer and SLOWLY peel the release liner away towards the center masking hinge. Be careful not to touch the adhesive side of the vinyl transfer. Use scissors to cut away the excess release liner and discard.
Step 5 Hold your vinyl transfer by the application tape, careful not to touch the vinyl adhesive to the application surface until you are ready to squeegee. Beginning at the center hinge, make easy overlapping, pushing strokes with your squeegee. Remove the center hinge tape and slowly peel the remaining release liner away. Squeegee the other half of the vinyl transfer, working from the center to the edges.
Step 6 To remove the application tape, peel SLOWLY at a sharp (180°) angle. If the vinyl appears to be lifting, gently push the application tape in the opposite direction from which you were pulling and resqueegee that area. If after removing the application tape, air bubbles are apparent, puncture the vinyl with a pin or needle (DO NOT USE a knife or razor blade) and squeegee out the air towards the puncture.
Please refer to TFX Pro System for additional application procedures.
Wet Application Method:Spraying POSITION PERFECT onto your application surface will delay the adhesive activation between the bonding surface and vinyl transfer, resulting in a bubble-free, wrinkle-free application. CAUTION: Wet application may delay the immediateremoval of the application tape. A waiting period of up to 30 minutes may be necessary.
Order History
Policies | Installation
Copyright ©
